Damit Dam Sealer - 20 Liter

The polymer is applied to a leaking dam or pond by scattering the powder across the surface of the water. DamIt Dam Sealer is designed with a positive charge which draws it downward through the water toward the bottom of the dam or pond.

The water pressure (hydrostatic pressure), which causes the dam or pond to leak, forces the polymer down into cracks and crevices as it sinks to the bottom of the pond or dam.

Once activated with water, the polymer will expand in size and bind to other polymer particles to form larger groups of particles, which effectively slows and stops the leak.

The polymer will continue to expand over several hours and forms a flexible plug that withstands water pressure. The positive charge of the particles will also attract any silt and suspended matter in the water downward to the bottom, which acts to embed the polymer within the soil structure and minimise any disturbance or movement of the polymer that may be caused by future water inflows.

DamIt Dam Sealer is insoluble and will form a long-term plug, in cracks and porous soils.

The polymer stays active when wet and can withstand continuous wet/dry cycles to accommodate rising and falling water levels due to seasonal water level variations in the dam or pond.

The polymer is totally safe and approved for use with potable water and will not harm humans, fish, aquatic plants or animals.

DamIt Dam Sealer will eventually break down to form a harmless mix of water and carbon dioxide over time.

DamIt Dam Sealer is a rapid, cost-effective solution for sealing water leaks and does not require earthmoving equipment or the emptying of dams and ponds; allowing you to save valuable water and keep the dam or pond in use while repairs are undertaken.

DamIt Dam Sealer works on a wide range of soil types; from clays to sandy loams and in a wide range of water types; from clear, pure drinking water through to saline water with high levels of suspended clays typically found in rural stock dams.

One application is normally sufficient to stop leaks permanently. However, each earth dam is built/constructed differently. There are also a wide variety of different soil types that needs to be considered. Therefore, it is important to note that more than one application of DamIt Dam Sealer may be required to seal an earth dam.

DamIt Dam Sealer is applied over the surface of the dam/pond at a rate of 1 litre of DamIt Dam Sealer powder per 10 square meters (or 107 square feet) of dam. If you have obvious signs of the leak (e.g. wet walls or water trickling out of ground), or you feel you know the general area causing the leak then DamIt Dam Sealer can be applied just to those areas of the dam/pond and a smaller amount of DamIt Dam Sealer will be required. Allow 1 x 20ltr pail per 200m2 of surface area.

Detailed Project Instructions, Application Guide and SDS are available on the Aqua Plastech website

Products uses
- Rural and Farm Dams (Not Concrete)
- Garden or Park Ponds (Not Concrete)
- Golf Courses
- Levee Banks
- Irrigation channels/ponds
- Storm-water Channels
- Artificial Wetlands
- Tailings Dams
- Fish Ponds (Not Concrete)
- Aquaculture

Not suitable for highly acidic or alkaline tailings

If you don't know your dam surface area in square meters; the coverage rate for DamIt Dam Sealer is 1L: 10m2 or a 20L bucket will be enough to treat an area of 200m2.

If your dam is circular measure the distance across (diameter) and use the following formula to calculate area - 0.785 x Diameter x Diameter. Eg distance across dam is 10 meters, area is 0.785 x 10 x 10 = 78.5m .

We're always happy to assist in calculating the amount required. If you aren't sure or have a difficult shape please use the Contact Us page and send details of your project.

Disclaimer

Customers are advised to consider the information in this data sheet in the context of how the product will be used, including surfaces and any other products used. The information provided in this data sheet represents our best scientific and practical knowledge. Any advice, information or assistance provided by Shalex in relation to its products is given in good faith, however is provided without liability or responsibility. Due to the wide variety of site conditions we are unable to assume liability for any loss that may arise from the use of our products. The user is responsible for checking the suitability of products for their intended use.

CAUTION
DamIt Dam Sealer becomes very slippery when wet. The use of gloves is suggested when hand spreading to keep DamIt Dam Sealer dry until ready for use. The container must be well sealed in high humidity to stop absorption of moisture, by the polymer, prior to use. Discard any polymer powder which has been wet, forms lumps, or a slippery gel consistency.

TECHNICAL DATA
Application - One application is normally sufficient however difficult projects may require follow up application
Coverage - Normally applied at 75g/m2 of dam/pond surface area.
For high salinity increased dosage rates are required. 1Ltr normally covers up to 10m2 of dam/pond surface area
Activation Time - 0-2 hours
Fully Activated - 4-7 days
Expected Life in Soil - 8 -10 years
Shelf Life - 5 years in a dry sealed container
Store Between - 0 degrees Celsius - 50 degrees Celsius
Application Temperature - Water temps above 5 degrees Celsius
Clean Up - Sweep up spills of dry DamIt Dam Sealer or, if wet hose off with large amounts of water